| This is the FASST 2.4GHz Futaba 12ZHP Computer Radio on Mode 2
with the R6014FS Synthesized 14-Channel Receiver.
Does not include servos.
This is the helicopter version which will default to heli settings
when powered up and does not have a ratcheted throttle stick.
If your transmitter's region code is something other than the United
States,the TM-14 Module sold in the United States is not compatible with this
transmitter. As such, it is necessary to purchase the TM-14 module which
matches the region code of the transmitter.
The Futaba 12ZHP shares many features with the 14MZ such as
Dual Internal Processors, Real-Time Response with 2048PCM,
Fully Synthesized Receiver, Servo Grouping, Variable Dual Rates and
Quad-Bearing Gimbals
**** While you can obtain a 50MHz module for this radio, it can only be ****
******* purchased through the service center at 217-398-8970 opt 2 *******
**Additional Technical Info Will Be Added When It Becomes Available.**
FASST FEATURES:
Futaba's FASST (Futaba Advanced Spread Spectrum Technology) shifts
very quickly virtually eliminating signal conficts and
interruptions unlike other 2.4GHz systems that only stay on one
or two frequencies
Dual antenna diversity enables FASST system to automatically and
seamlessly select the best reception between the two antennas
built into the receiver ensuring that the aircraft stays under
constant control of transmitter regardless of altitude
Pre-Vision Packet Screening technology scans incoming data for
potential problems and applies sophisticated error correction
techniques for solid impenetrable link with model
Easy Link system features a unique ID code in the transmitter that
links to the receiver insuring that receiver only follows commands
from this transmitter-with over 134 million possible codes there
is no chance for a conflict
No hassle Fail Safe programmed through transmitter-no complicated
set-up steps or binding plugs
When performing a ground check, the Power Down function allows
modeler to reduce power from up to 50+ paces away-like
retracting the antenna on a conventional transmitter
Purpose built custom IC chips for key functions; no off-the-shelf IC
chip
GENERAL FEATURES:
Dial-N-Key jog dial with joy stick button allows cursor movement in
four directions for very user friendly programming
PCM G3 2048 resolution is "backwards compatible" with 1024 PCM, and
FM/PPM
Supports 13 different wing types, 3 tail types and 3 motor types
Supports eight flight conditions (seven plus the default)
Stores memory for up to twenty-five models
245 model memory available with optional 32MB Compact Flash Card
available separately, (FUTM9410)
Six factory-set Variable Dual Rate (VDR) curves can be assigned to
any function in any flight condition configuration
Variable Dual Rates (VDR) and Expo can be combined so they are
automatically activated when a function is activated, no program
mixing required
Dual Internal Processors allow one processor to be devoted to flying
functions while the other processor focuses on non-flight
functions such as input and communications
7.4V 2200mAh Lithium Ion transmitter battery (FUTM1475) for long
operating times
R6014FS Receiver;
Retains G3 2048 resolution and Futaba Real Time Response from the
72MHz version.
Simple one-touch binding - no plugs to mess with or lose
A full range system for all aircraft from giant scale to
Park Flyer applications-no need to buy separate receiver for
specific aircraft
Dual Antenna Diversity allows 2.4GHz FASST Futaba transmitter to
select the best reception between the two receiver antennas with
no signal loss
Rubber grommets installed where antennas exit to eliminate stress
and fraying of the two antenna wires
Servo Grouping;
Multiple servos controlling a single function can be set up
through the transmitter and then plugged into differently
adjustable receiver channels (even non-consecutively) without
needing a separate servo synchronizer for mixing.
Quad-Bearing Gimbals for smoothest motion and response, stick tension
and detent are adjustable
Seven color LED indicator
INCLUDES: 12ZHP Synthesized Transmitter (not available separately)
FASST TM-14 Module (FUTL8934)
R6014FS Receiver (FUTL7644)
FLT2F2200 7.4V 2200mAh Lithium Ion Transmitter Battery (FUTM1475)
LBC-1D5 Lithium Ion Transmitter Battery Charger (FUTM1700)
NR4F NiCd 1500mAh Receiver Battery (FUTM1285)
FBC-32B Wall Charger for Receiver Battery (FUTM1705)
DSC Cable (FUTM4243)
Switch Harness with Charge Cord (FUTM4387)
Padded Aluminum Case with two Keys (not available separately)
Woven Orange Neck Strap (FUTM5693)
One each 1.5mm and 2.5mm Hex Wrenches
Instruction Manual
REQUIRES: Charging batteries before use
Servos of modeler's choice, suggested servos for use with the 12Z
include the Futaba S9154 Digital High Speed Servo (FUTM0214) and
the Futaba S9255 Hi-Torque Heli Digital Servo (FUTM0225)
SPECS: Transmitter;
Operating System: 2-stick, 12 channels, PCM-G3 synthesizer system
Modulation: PCM-G3, PCM 1024, or FM/PPM switchable
Power Supply: 7.4V FLT2F2200 Li-Ion Battery
Current Drain: 500mA average
R6014FS Receiver;
|
